DigiTire
Suppliers of Electronic Tire Pressure Monitoring Systems
The TPMS-201 is designed to monitor 4 wheels and hence is designed for 4 wheel vehicles only. The kit is supplied with 4 sensor assemblies which need to be fitted to each wheel of the vehicle. Each of the sensors consists of a valve stem, incorporating the new tyre valve and electronic assembly which is encapsulated within a plastic/silicon housing.
The actual electronics within the sensor consist of a low power 433.92Mhz RF transmitter, a microprocessor with embedded temperature and pressure transducers, a motion detector and a lithium battery as a power source. None of the electronic components, including the lithium battery are serviceable or replaceable. In the event of a failure the whole valve sensor assembly can be replaced.
The sensors need to be fitted in place of the existing tyre valves. To do this the tyre needs to be removed from the rim, the sensor fitted and then the tyre re-fitted. Normally this work is carried out most efficiently by a specialised tyre fitter or tyre retail outlet. Only rims with a tyre valve mounting hole of 11.3mm are supported. This is the standard size for most OEM and after market rims.
The battery life of the sensors has been designed to last for 7 years (typical) or 250,000km of driving. The concept being that if a set of sensors is fitted to a vehicle at the time that a new set of tyres are fitted, the sensors will outlast the life of the tyres. As that set of tyres is replaced, it can then be determined whether the sensors should be replaced or whether they can be utilised for another tyre cycle.
The valve stem section of the sensor assembly is manufactured from a high grade aluminium with a propriety finish to prevent corrosion. Aluminium is utilised to ensure the sensor assembly weight is kept to a minimum, while at the same time providing mechanical strength.
This low weight is essential to ensure that wheel balancing can be easily achieved. Under certain environmental conditions electrolysis can occur if a steal valve cap is fitted to the valve stem. This electrolysis will cause the valve stem to corrode. As a result it is recommended that only the supplied plastic or an aftermarket aluminium valve cap be used.
The encapsulated electronics will ensure reliable operation even in dirty, muddy and humid environments. In addition the encapsulation will also ensure the sensor can withstand heavy vibration from rough dirt roads or even motor racing applications. As all the electronics are environmentally and mechanically insulated and isolated, including the lithium battery, the unit is not serviceable in any way, nor can the battery by replaced.
Additional sensors can be purchased and fitted to spare tyres, however only 4 wheels can be monitored at any one time. Tyres can be easily rotated along with spare tyres due to Digitire ’s patented sensor ID technology.
TPMS-201D (1.8 - 6.0 Bar) - R2,295.00
SENS-201 spare sensor - R450.00
TPMS-201D suits for all vehicles including light trucks, vans and mini buses with manufacturer´s recommended cold inflation tire pressure between 1,8-6,0 bar. Monitors tire pressure 24/7, also when the car is parked.
This system is programmable, cold inflation tire pressure can be programmed between 1,8-5,0 bar and it is possible to program different cold inflation tire pressures for front and rear axles. To program the values of cold inflation tire pressure for your vehicle, firstly inflate your tires exactly to required level and press briefly the knob on the rear panel of the display, it shows now the factory preprogrammed values. If you wish to change these values, press and hold down the knob on the rear panel of the display for 5 seconds until all zeros appear. Now you have to drive approximately 25-30km/h until the data received from the sensors will be recorded in the memory as the new values for cold inflation tire pressure. This procedure can be repeated, by changing the tire pressures different cold inflation pressures can be recorded. The programming must be done only with cold tires.
Whilst both permanent wire and cigarette lighter connection cables are included in the kit, 24-hour permanent wire connection is recommended.
By pressing the button on the front panel of the display the user can check either the four tyres pressure or temperature. The backlight turns off automatically in 10-seconds.
In addition to pressure and temperature indications this system gives following warning signals:
- high pressure - 30% higher of cold inflation pressure
- low pressure - 20% lower of cold inflation pressure
- high temperature - 80°C
- air leakage - change of pressure 0,44 bar in 15 seconds
